Description
$79.99 With Coupon Code FlashSale
Built from CNC-machined 4140 steel (NOT Plastic) Heat-treated for indestructible strength and finished with a badass DLC coating, this kit laughs in the face of wear and tear.
The FLAT trigger comes pre-milled with precision Super Safety cuts, ready to drop in and dominate right out of the box. No gimmicks. No compromises. Just pure, unrelenting performance. Upgrade or get left behind.
Includes: FLAT face Mil-Spec Trigger, Cam, Lever and Safety Detent Pin. Drop in and GO!
Wholesale Inquiries contact: [email protected]
PLEASE NOTE: NOT available for sale in: CA, CT, DC, DE, FL, HI, IA, IL, MA, MD, MN, NJ, NY, RI or WA
WHAT IS A SUPER SAFETY???
The Super Safety Trigger System refers to an advanced combination of an upgraded safety selector and a precision trigger, typically designed for AR-style rifles. This system is aimed at improving the overall functionality, responsiveness, and safety of the firearm.
Please note: May not work in the following lower receivers:
The lower receiver must be a low shelf lower receiver if it is a high shelf receiver it will require dremeling down so the bar can go back enough for the BCG to clear and fully cycle.
Colt - May have a bar in the lower designed to prevent “certain FA” parts from going in the lower.
This is not compatible with AR-10/LR-308, AR 12GA, AR 22LR, or any platform not using a typical FA M16 BCG.
When first used, if you experience light primer strikes or hammer follow symptoms (typically 1-2 rounds are fired then the trigger is dead), you should replace the buffer with an H2 or H3 buffer. You may also adjust the gas block, if equipped. This resolves the issue in 99% of scenarios and we recommend using a H2 buffer to start.
Do these fit in all AR-15s?
They should. There is no guarantee, but as long as it is made according to mil-spec, it should fit fine. There are some high shelf lowers that need to be machined/dremeled open to allow clearance (Colt is the most notorious, but some others may be high shelf or have blocks, please see below). There are many uppers that almost clear the lever, but usually require a Dremel to cut the upper pocket back to the locking lug. You will likely need to go from a H buffer to H2 or H3 for reliability if you get light primer strikes/hammer follow.
Comments (17)
I haven't bought from Wise Arms in quite some time, but I will chime in on two things:
At one point I bought several things from Wise Arms (8 totals order from my email receipts) from 2014 to 2018. Never any issues, all good products.
Sadly, my last order (for 4 blem receiver extensions) was less than satisfactory. The items were described as 'blems', however, they were all milled too shallowly, essentially not allowing the BCG to go far enough into the tube to be able to lock back. The difference between a known good receiver extension internal depth and the 'blems' from Wise Arms was only ~4mm but that is enough to make them non-functional (see pic).
I had previously corresponded with the owner and dropped an inquiry on the tubes, but I sadly never never received a reply on the 4 tubes. I still have them sitting in my build cabinet on the off chance I can use one on a AR stock adapter for something that does not need a BCG, but for an AR build they are unworkable. I would not have classified these as blems, nor were they listed as being milled short, just blems.
That was my last order with Wise, which I was sad about as I had had very good experience with the vendor for 4 years. I don't post this to be petty or vindictive. The total price of the order was quite small and easily passed aside, however, I had been seeing this thread pop up lately and debated about sharing my experiences with the vendor.
He/they are legitimate and do fulfill orders, I just had one poor experience out of 8 total orders. An email response from the vendor and it could have probably been made good at the time.
Got a similar kit several months ago from some guys in Daytona FL. Crappy finish, sloppy tolerances, did not work as expected, so I mailed it back for refund. Still no refund, no peep. Beware of shady sellers.
So what does this have to do with this particular vendor or item? That's like complaining you bought a bad Chevrolet vehicle while sitting in the mechanics bay at a Ford dealership... SMH...
Yep the are legit I just ordered the Glock RST from them no problem. Rec'd it a few days ago.
I can vouch for Wise Arms. Haven't ordered anything from them for years but they are legit. Used to buy AR Uppers and other parts from them when I was into building.
I would love to know why you think this is a scam. We have been in business since 2013 and steadily growing. If we were scamming people we would have long been out of business. Looking at your posts over the years looks like 90% negative.
Did you ever fix the issue user Janizary (second to top comment) had? Apparently he contacted the owner and never recieved a reply on his blem products. Seems like a massive oversight, or potentially a "do not buy" scenario if customer support doesn't reply to issues. You responded to this guy leaving negative feedback, but skipped the comment from the actual customer who seemed to have a legitmate issue. And if you check my post history, you'll see well over 90% are postive and/or helpful.
Don't sweat it. We members can sniff out a troll vs a legitimate complaint. All the long time sellers on here all have some b.s. reviews or stupid troll comments and down votes. Take it like a badge of honor that your legitimate! Haha
You have something brown on your nose, sailor.
What a screenname for that comment CleavelandSteamer69
no way they are trying to say wise is a scam lolll
Website looks pretty janky on iOS. I prob wouldn’t trust it either.
It’s a scam. Good luck getting your money back.
i ordered 2 FRT and received both and was delayed a bit so they gave me a free tx22 FRT so i am good with them will be ordering again very soon..